SERVICE

All categories
/
Operating procedures

Operating procedures

  • Categories:Service
  • Time of issue:2019-10-16 00:00:00
  • Views:0
Description:
Description:
Information

  Note for maintenance personnel

  1. Only those who have passed the training can overhaul and debug all equipment.

  2. Do not replace any parts without permission.

  3. Do not connect wires without permission.

  4. You must master the computer's operating methods. If an alarm sounds, you need to find the cause and troubleshoot the machine before you can test the machine.

  5. After the repair is completed, the hand wheel must be pushed by hand, and it can work if it is smooth.

  6. ​​Do preliminary maintenance every week. Add 68# oil to each shaft to ensure the cleanness of the screw.

  Computer Numerical Control Drilling Machine (Flocking Machine) Operating Regulations

  1. Scope of application

  This standard is applicable to the safety operating procedures of hair planting equipment

  2. Main content

  (1) Those who have not been trained are strictly prohibited from on-the-job operation.

  (2) Keep the surrounding materials of the fuselage neatly placed before turning on the machine, and do not collide with the fuselage and wires.

  (3) The operator should wear overalls, caps (eyebrows, sideburns, buns), and cuffs should be tightened. It is strictly forbidden to go to work with shawls and long hair.

  (4) Before starting the machine, check whether the amount of oil in the oil tank is sufficient and whether the oil circuit is unblocked, and press the lubrication button.

  Slide chart cards for lubrication work.

  (5) Power-on method: Turn on the power switch first, turn on the "OFF" system to enter the working mode after about four seconds, and turn the control box to the step-by-step and test mechanism. If it is normal, it can be automatically operated.

  Industry.

  (6) It is strictly forbidden for two or more people to operate the same machine.

  (7) The operator must concentrate, and it is strictly forbidden to leave the work post during the operation of the machine. If an abnormality is found, press the "Pause" button immediately and inform the relevant personnel for maintenance.

  (8) It is strictly forbidden to contact any part of the body with the running machine during work. It is strictly forbidden to disassemble the protective device without permission.

  (9) It is necessary to turn off the machine after the work is completed. The "ON" system should be turned off first, and then the power switch should be turned off after 4 seconds.

  (10) The body, computer and control box must be cleaned every time before get off work, and the corresponding parts must be lubricated.

  (11) Observe the above operation rules, strengthen machine maintenance, improve production efficiency, take care of company property, and protect your own safety.

  Computer numerical control drilling and tufting machine operating instructions

  1. Those who have not been trained are strictly forbidden to work on duty.

  2. Keep the materials around the fuselage neatly placed before starting up, and do not collide with the fuselage and wires.

  3. Power-on method: turn on the power switch first, and then push the computer switch to the "ON" system after about four seconds to enter the working mode, and switch the control box to the step-by-step and trial mechanism. If it is normal, it can operate automatically.

  4. It is strictly forbidden for two or more people to operate the same machine.

  5. The operator is attentive, and it is strictly forbidden to leave the work post during the operation of the machine. If an abnormality is found, press the "Pause" button immediately and inform the relevant personnel for maintenance.

  6. It is strictly forbidden to contact any part of the body with the running machine.

  7. Turn off the computer after finishing the work, turn off the computer "OFF" first, and then turn off the power switch after 4 seconds.

  8. The fuselage, computer and control box must be cleaned every time before get off work, and the corresponding parts must be lubricated.

  shearing machine operating rules

  one. Operating procedures

  1. The operator must be trained and qualified before operating this machine.

  2. Before turning on the machine, check whether there is any debris on the cutting edge to ensure that the machine is clean.

  3. Check whether the barometer is within 5-6 Bar before turning on the power switch.

  4. Place the brush in the fixture correctly and check whether it is automatically clamped.

  5. After visually checking that the product is firm, press the "Start" button to perform automatic work.

  6. When the work is finished, the power switch must be turned off.

  two. Maintenance and safety matters

  1. Make sure the body is clean.

  2. Lubricate the guide shaft of the worktable regularly.

  3. It is strictly forbidden to operate the same machine by two or more people at work.

  4. It is strictly forbidden to contact any part of the body with the machine in operation.

  shearing machine operating instructions

  Step 1: Material preparation

  1.1 Put the product to be sheared on the left side of the fuselage, and put the sheared turnover box at the product outlet.

  Step 2: Turn on

  2.1 According to the "Operation Regulations of Shearing Machine", turn on the machine correctly and start the main knife operation.

  Step 3: Work

  3.1 Pick up the product with the left hand, and check the rough surface for stains, hair leakage, and scratches.

  3.2 After checking, the hair side is facing upwards, the brush handle is put into the fixture forward, and then the brush handle is automatically locked when you look at it visually, otherwise you can manually clamp the switch to clamp the brush handle.

  3.3 Press the "Start" button to perform automatic shearing, and automatically let the product slide into the turnover box after the work is completed, and wait for the next action.

  3.4 The first piece is confirmed to be qualified: the length of the floating surface of the wool, when the wool end is flat and covered

  front, stains, scratches and other phenomena.

  3.5 The operations of 3.1, 3.2, 3.3, and 3.4 can be repeated only after the first article is confirmed.

  3.6 Arrange and arrange the sheared products into the turnover box.

  Step 4: Finish the work

  4.1 Clean the fuselage and tidy up the materials.

  4.2 Refer to the "Computer Numerical Control Hair Planting Machine Operating Regulations" to shut down correctly.

  Precautions:

  1. Must be trained, qualified personnel can be on duty to ensure safe production.

  2. Strengthen machine maintenance and improve product quality.

  3. Clarify product quality standards and control the flow of defective products into the next process.

Scan the QR code to read on your phone